The following list provides a quick summary of the most necessary and commonly used configuration commands (see the sstpfb_sample.cfg file included in the distribution):

If using the point data model:

If using the Cascade DataHub:

The following file could be used to initialize card number 0 for port 0x250 and hardware address 0xCC00. This file, sstpfb_sample.cfg, is included in the driver distribution.

;;;
;;; Sample Driver Configuration File for the DR5136PFB Driver
;;;	Modify to suit requirements of specific system

;;;
;;; Set driver debug/error reporting level:
;;;	(debug level)
;;; where
;;;	0 for no output (only terminal errors produce output)
;;;	1 or 2, normal setting, reports errors and other significant events
;;;	3... reports increasing levels of debug information
(debug 2)

;;;
;;; Initialize card(s) 
;;; ------------------
;;; (cardInit [id [port [addr [irq]]]])
;;;
;;; id	 	is 0-3, the id for the interface card (default is 0)
;;; port	for ISA cards, the port address set by the SW1 switches
;;; addr	for ISA cards, location of 16K memory window
;;; irq   	for ISA, interrupt number, or -1 for polling mode
;;;
; probe for all PCI cards available, use interrupts
(cardInit)
; init card 0 at port x260, using 16K memory block at xCC00, polled
;(cardInit 0 0x260 0xCC00)
; init card 0 at port x260, using 16K memory block at xCC00, using interrupt 7
;(cardInit 0 0x260 0xCC00 7)
;(cardInit 0 0x250 0xCC00 0 PFBPROFI.SS1)

;;; profile the cards
;(cardProfile)

;;;
;;; polled cards must have a specific polling period (ms) assigned
;;;
;(cardPoll 0 10)

;;; Publish alternate driver name to Cogent nameserver (see nserve and nsnames)
;(attachNS myName)

;;;
;;; Configure and Start Profibus Activity
;;; --------------------------------------
;;;

;;; load some helpful command definitions
(include /usr/cogent/src/dr5136pfb/pfbDefines.cfg)
(include /usr/cogent/src/dr5136pfb/pfbDpMaster.cfg)
;(include /usr/cogent/src/dr5136pfb/pfbDpSlave.cfg)
;(include /usr/cogent/src/dr5136pfb/pfbFdlMsg.cfg)
;(include /usr/cogent/src/dr5136pfb/pfbFdlSap.cfg)

(pfbNetParms 0 0 ACTIVE BAUD_1m5 * (bor OPTION_REPEATER OPTION_FMS))
; just report the default bus parameters
(pfbBusParms 0)
; attempt to determine the slave configuration using SST's auto feature
(pfbLoadCfg 0 AUTO)

(pfbOnline 0 DpMaster)
; enable input and outputs
(pfbRunMode 0)

;;;
;;; Connect to the DataHub
;;; ----------------------
;;;  Enable connection to Cascade real-time datahub
(datahub y)

;;;  Publish status driver status
;(statusPointDefine)

;;;
;;; Analog and digital points are created through the generic commands below,
;;; where address = 
;;;		[[card:]buffer:]word[;flags]
;;;			for 16-bit analog values
;;;		[[card:]buffer:]word.bit_ofs[;flags]
;;;			for digital bit values
;;;		[[card:]buffer:]word.bit_ofs[.bit_width[;flags]]
;;;			for digital fields
;;;		   
;;; card	0..3 card id
;;; buffer	0 master write, 1 master read, 2 slave write, 3 slave read
;;; word 	16 bit word offset into buffer memory
;;; bit_ofs	1..16 bit offset into word
;;; bif_width	1..32 width of field in bits.
;;; flags 	-e0 | -eN (endian swap), -s (signed value)
;;;
;;; NOTE: Points MUST be collected into a group (see below) to be updated automatically
;;; -----
;;;
;;; Cogent-specific testbed configuration (ref for point definitions examples) is in
;;; (include /usr/cogent/src/dr5136pfb/testbed.cfg)

;;;
;;; Define analog points
;;; (analog enable-flag name address R|W|RW cycle-millisecs exception-flag
;;;  raw-min raw-max eng-unit-min eng-unit-max)
;;;
;(analog t <name> <address> r 0 t 0 32767 0 <max>)

;;;
;;; Define digital points
;;; (digital enable-flag name address R|W|RW cycle-millisecs exception-flag)
;;;
;(digital t <name> <address> r 0 t)

;;;
;;; Define groups.
;;;	Groups collect together a set of points to be automatically updated.
;;;	The update can occur on the group's specified cycle interval,
;;;	or can be linked to the card's update cycle, using the cardGroup command below.
;;; (group enable-flag name address R|W|RW cycle-millisecs point...)
;;;
;(group t <name> 0 R <ms> inpnt1 inpnt2 inpnt3)
;(group t <name> 0 RW <ms> outpnt1 outpnt2 outpnt3)

;;; 
;;; Associate a group with the cycle of the card (group's cycle-millisecs must be 0)
;;; (cardGroup 0 groupName)
;;;
;(cardGroup 0 <name>)

;;; ------------------------------------------
;;; Check profibus status (for setup/debug)
;(pfbStationStatus 0)
;(pfbDiagStatus 0)